Made in France in an ESAT supported employment workshop

The universal filter.
Tailored to your needs.

Graphite, Safran or Azur.
Choose your media, adjust the pleats,
then cut to the size of your grid.

I try the cutting Compare the three media

From €12.90 TTC · Graphite PM · by filter

On compatible metal grid. Clips optional.
The range of universal pleated filters FAC : Graphite grey, Safran yellow and Azur blue, with orange clips optional 01 Mesurer 02 Cut 03 Poser
3 colors · 3 requirements22 or 48 pleats · cut to sizeFilters made in France · in ESAT

The cutting workshop

Your grid.
Your cut.

Two measurements, a plot, then the installation. Prepare the cutting of your pleated filter on the useful surface of a metal grid.

  1. 01 Mesurer
  2. 02 Cut
  3. 03 Poser

Let's start with your grid.

Measure a single grid, inside the frame.

cm
cm

A, along the accordion pleats: fixed width to be cut, up to 26,6 cm in PM, 40 cm in GM.

B, perpendicular to the accordion pleats: the side that opens like an accordion. Its length depends on pleat spacing and must be checked on the filter.

I have the filter: check its deployment
cm

Optional. Measure the media after adjusting the pleats to the support. Do not flatten them just to reach a given length: keep suitable airflow.

Your filter

Graphite : follow the direction indicated in the instructions.

To your measurements

PM or GM ?
Preparation of the cutting and installation Type A and B to display your plot. Principle illustration, not a stencil to print.
The accordion pleats shown do not give a maximum unfolded length. This drawing is not a cutting template, but a simple diagram of the process.

One grid, two measures.

Measure the usable area and check the clearance on the motor side.

Simulation prepares the gestures. Check the deployment, the support and the air passage on your support before any actual cutting.

To prepare the following

Choose your measurements to see the size to be examined.

The metal bracket is not included. The filter and clips are to be selected separately.

The right spacing also makes the difference. For the same frame area, tighter pleats retain more filter media. Stretching the filter flattens the pleats and reduces media density. Adjust them to the support while maintaining suitable airflow. See the complete guide to choice and installation

Before the actual cutting

This guide is for recirculating cooker hoods with a suitable metal support. The media is not a direct replacement for a round bayonet filter. Keep the metal grease filter. Follow the cooker hood and filter instructions and check motor-side clearance, airflow and fixing points.

With clips: distribute 4 on the one hand and 4 Without clips: the housing must ensure that the media is held in place without contact with the motor or disturbance of the ventilation. If in doubt, send a photo of the media and housing before ordering.

Read the complete guide to choosing and installing

02 / Your need

Three colors. The choice is clear.

All filters in the range contain activated charcoal, so choose the right one for your kitchen.

Universal pleated charcoal filter FAC Safran : weight, adjustable accordion pleats and laying on metal grid

Activated charcoal · 450 g/m²

Safran

For stronger cooking odours.

A yellow odour-control layer complements the activated charcoal. Designed for everyday cooking, including fish, garlic, spices and fried foods.

Universal pleated charcoal filter FAC Azur : weight, adjustable accordion pleats and laying on metal grid

Activated charcoal · 450 g/m²

Azur

Antibacterial-treated filter media.

Activated charcoal with an antibacterial treatment that helps limit bacterial growth within the filter media.

The treatment acts in the filter media; it does not disinfect the room air.

Your selection

Choose your pleated filter.

The models below are available in the shop. The clips are selected separately.

There are 7 products.

Showing 1-7 of 7 item(s)

Charcoal media you can cut to fit

What about an air conditioner, deep fryer
or a vacuum cleaner?

The charcoal media can be cut for other air-filtration systems with a housing designed for a compatible activated charcoal sheet, such as an air conditioner, a deep fryer with an odour-filter compartment, a vacuum cleaner or a ventilation unit.

Suitability depends on your appliance. The appliance instructions must permit this type of media. Check the dimensions, thickness, temperature, airflow and fittings. Keep the filter securely inside its intended housing without obstructing ventilation.

In a vacuum cleaner, it can complement a suitable odour-filter stage; it does not replace a dust filter, motor filter or HEPA filter. In a deep fryer, use only the intended filter compartment, away from oil, food and heating elements. FC116 clips are intended for compatible metal cooker hood frames.

Send your appliance model number and a photo of the filter housing if you would like us to check the proposed fit.

pack of 16 clips orange FAC FC116 to keep the pleated filter

FC116 fixing clips · Pack of 16

03 / Secure the media

Good support,
with or without clips.

On a compatible frame, FAC FC116 clips hold the media against the metal grease filter. If the housing already holds the media securely and clearance is limited, installation without clips may be suitable after checking your cooker hood.

4on one side+4on the other= 8

With clips: use 8 per filter. A pack of 16 is enough for two filters.

Clips are sold separately from filters. The metal support is not included. Check that the clips fit your frame.

View the pack of 16 clips

Install in three steps

Measure. Cut. Secure.

Keep your cooker hood’s metal grease filter in place: it supports the charcoal media.

  1. 1

    Measure the support

    Measure the usable area and check the clearance on the motor side.

  2. 2

    Adjust the media

    Gently open the accordion pleats, then cut the media to the dimensions needed. Follow the installation direction for your chosen colour.

  3. 3

    Secure and refit

    Distribute the clips along both sides of the frame. Without clips, the housing must hold the media securely, away from the motor and without restricting ventilation. Check the fit, then refit the frame as instructed in the cooker hood manual.

French know-how,
a workshop engaged.

The filters FAC are manufactured and packaged in France in ESAT. The folding and packaging involves workers with disabilities.

Choose with confidence

Your questions before ordering.

Is this filter suitable for all cooker hoods?

For recirculating cooker hoods with a suitable metal support. Check dimensions, clearance and fittings. It is not a direct replacement for a round bayonet-fit filter.

Are the metal filter and clips included?

Each filter reference includes one piece of pleated charcoal media. The metal support is not included. FC116 clips are sold separately in packs of 16.

Are clips still needed?

No: it depends on the support. Clips fit compatible metal frames. Some narrow housings may hold the media securely without clips. Send photos of the support and housing if you are unsure.

Which way round does it go?

Safran: charcoal side towards the motor. Azur: blue side towards the motor. For Graphite, follow the orientation shown in the instructions. Also follow your cooker hood manual.

When should I replace the charcoal filter?

Replacement frequency depends on how much you cook and use the hood. Follow the instructions and replace the media when it is saturated or cooking odours persist.

Unsure about your support? Send us a photo before ordering.

Have my cooker hood checked

Pleated Universal charcoal filters FAC : Graphite, Safran anti-odor enhanced, Azur with antibacterial treatment of the media. Formats 22 and 48 pleats to cut to size, with clips FC116 sold separately.

You were looking for the old filter FC99 de 47 × 57 cm ?

The old flat media FC99 is no longer sold. Explore our current range of universal pleated charcoal filters to cut to size, made in France in an ESAT : Graphite, Safran and Azur.

Choose the format according to the metal filters of your cooker hood: PM for a cooker hood of 60 cm with two metal grease filters; GM for a cooker hood of 60 cm with one large grease filter, or 90 cm with two or three grease filters. Adjust the pleats to the support; this is not a flat panel with dimensions identical to the FC99.

Check the motor side space and the holding on the metal bracket before installation. The clips are offered separately depending on the mounting.

Choose PM or GM and check the installation · Have my fitting checked with a photo